Details

 

 

How do you feel when it comes to How to Install a Bathtub?

Setting up a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently easily accessible, the project can move quickly; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will assist you install a brand-new bathtub in your bathroom if you have currently gotten a brand-new tub and don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

Firstly, the supporting frame supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final position.

 

 

Removing Old Touches

If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub up until the spirit level reads degree.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water supply and also examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leakages.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub needs to wait until the tub has been used a minimum of when as this will settle it into its last position.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the faucet and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a stiff seal, triggering the water to penetrate the wall in between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking the time to browse our short article. Do you know about somebody else who is fascinated with the niche? Do not hesitate to share it. Thanks for taking the time to read it.

Book With Us Today!